Fitment: For YAMAHA FZ8 (non-ABS) (2010–2015) For YAMAHA Bolt (non-ABS) (2013–2016) For YAMAHA YZF-R1 (2001–2008) For YAMAHA BT1100 Bulldog (2002–2006) For YAMAHA Diversion (non-ABS) (2009–2015) For YAMAHA Drag Star (1999–2006) For YAMAHA FJR1300 (non-ABS) (2001–2005) For YAMAHA FJR1300 (ABS) (2003–2005) For YAMAHA FZ-16 / FZ-S (2008–2015) For YAMAHA FZ400 (1997–2002) For YAMAHA FZ6 (non-ABS) (2004–2012) For YAMAHA FZ6R (2009–2016) For YAMAHA Stryker (2011–2016) For YAMAHA FZ1 (2001–2016) For YAMAHA FZ150 (2015) For YAMAHA FZN150 (2015) For YAMAHA FZ1N (2006) For YAMAHA FZS600 Fazer (1998–2003) For YAMAHA FZS1000 Fazer (2005–2015) For YAMAHA MT-01 (2005–2012) For YAMAHA MT-03 (non-ABS) (2006–2016) For YAMAHA Raider (2006–2016) For YAMAHA Roadliner (2006–2015) For YAMAHA Road Star (1999–2014) For YAMAHA Royal Star (all variants) (1996–2013) For YAMAHA V-Star (950cc and above) For YAMAHA Warrior (2002–2012) For YAMAHA WR250R / WR250X (2008–2016) For YAMAHA WR450R / WR450X (2008) For YAMAHA XT660 (2004–2015) For YAMAHA XV1600A Wild Star (1999–2005) For YAMAHA XVS950A Midnight Star (2009–2016) For YAMAHA XVS1300A Midnight Star (2007–2015) For YAMAHA YZF-R6 (2001–2016) For YAMAHA YZF-R6S (2006–2009) For YAMAHA Stratoliner (2006–2015) For YAMAHA TDM900 (non-ABS) (2002–2013) For YAMAHA TDM900 (ABS) (2002–2006) For YAMAHA XJ6 (non-ABS) (2009–2015) For YAMAHA XJR400 (2002–2007) For YAMAHA XJR1300 (2004–2016) For YAMAHA XV1900A Midnight Star (2006–2015) For YAMAHA XVS1100 Drag Star (1999–2006) For YAMAHA YS250 Fazer Condition: Light Source Color: Red / Blue / Green / White / Orange Item Name: Speed Gear Display Indicator Size: 4 cm × 4 cm × 4 cm (1.57 in × 1.57 in × 1.57 in) Features: - Displays current gear number - Indicates gears 1 through 6, plus neutral - Detects gear position faster than indicators using speedometer or tachometer signals - Mountable in any location Installation Notes: - Connect the gear display module to power and speed signal lines - Ensure cables are secured and not subject to steering-related damage Setup Procedure: - After installation, turn on ignition: display counts down from 6 to 1, confirming memory reset - Elevate rear wheel using a stand; start engine in Neutral (or perform setup while riding on a straight, low-traffic road) - Display shows “L”, indicating learning mode has started - Select first gear, release clutch, and maintain speed above idle - Display flashes “1”; continue accelerating in first gear - When display shows “2”, shift to second gear and continue accelerating - Repeat process for subsequent gears as prompted